Braeco » Product Categories » Pressure Control – Regulating Upstream

JBPH (set pressures to 5,800 psi)

titan — Tue, 24 Mar 2015 06:07:07 +0000

Model JBPH is a piston operated Back Pressure Regulator capable of set pressures to 5,800 psi (400 bar). It is suitable for gases and liquids and is available in sizes 1/2″, 3/4″ & 1″.

Body & Trim – 316L SS
Spring Housing – 316L SS
Plug – 416 SS
Seat insert – KEL-F
Body Seals – Buna-N, EPDM, Viton)
Cv 0.5 (class IV shut-off)
Ends – FNPT or BSPP, Socket Weld, Flanged

Spring Ranges – 0 -2,150 psi (0-148.3 bar)
0 – 2,500 psi (0- 172.4 bar)
0 – 4,060 psi (0-280 bar)
0 – 5,800 psi (0 -400 bar)

Options: Panel mount, Locking wire (lead sealed), Tamper proof, Lock-out device (these are explained in PDF)

The post JBPH (set pressures to 5,800 psi) appeared first on Braeco.

MK50 Back Pressure Regulator

titan — Tue, 24 Mar 2015 06:06:13 +0000

US manufactured MK50 has many of the same features as the MK60 Reducing Valve but the main difference is that it regulates/controls the upstream pressure. A high quality, long lasting valve which you can safely “set & forget”. Responds rapidly to pressure changes…….better control performance than most self-acting regulators…easily maintained and simple pressure adjustment in situ. Commonly used for Pressure Sustaining, Back Pressure control or as bypass valve for boiler feedwater. When installed in-line, they are used to guarantee upstream pressure to more critical services.

It is a robust, versatile, self acting valve that has sliding gate design (rather than conventional piston or plug and seat), has hard wearing Jorcote seats with class IV shut-off and Jorlon long life diaphragm. It is suitable to use with water, oil, gas, chemicals and steam. There are many variations to the basic model such as MK51 (high sensitivity, low droop), MK501 (high flow version) and MK50HP (high pressure version). In Bronze or DI version, valves have screwed ends BSPT, BSPP or NPT, WCB or 316ss valves can be threaded, socket weld, butt-weld or flanged to Ansi 150/300 or DIN PN10/16/25/40.
Maximum inlet pressure- BZ 3,400 kpa; DI 4,100 kpa; WCB/316SS 6,600 kpa
Maximum temp- BZ (260°C)/ DI/WCB/316SS (343°C)

Pressure Control ranges:
– MK50 ranges between 14 kpa-1,034 kpa)
– MK51 (ranges between 3 kpa-1,172 kpa)
– MK50HP 1/2″-2″ (ranges between 517 kpa-3,100 kpa)
– MK50HP 2″-4″ (ranges between 172 kpa-552 kpa)

* Options: Low flow trim in all sizes, special coated seats, 316SS or Monel diaphragm, cryogenic extension, Oxygen cleaned, salt water trim, Companion flanges for Bronze & DI valves, BSPP ends

The post MK50 Back Pressure Regulator appeared first on Braeco.

MK58FT 58A Back Pressure Reg

titan — Tue, 24 Mar 2015 06:05:55 +0000

MK58 is a globe style Back Pressure or Pressure Sustaining valve that offers high capacity, accurate regulation and easy servicing (bottom entry design makes it easy to clean or repair). It is available with hard seat (Class IV shut-off) or soft seat (class VI) and applications where the differential pressures do not exceed 300 psi (21 bar). Suitable for water, oil, gas, steam & chemicals. MK58FT has straight through flow with the excess pressure being relieved out through the bottom port. MK58A has the straight through port plugged and relieves out though the bottom port (see diagram on PDF)

Maximum inlet pressure- BZ/DI/WCB/316SS (2,100 kpa)
Maximum temp- 93°C Buna plug & diaphragm; 177°C Viton plug & diaphragm; 260°C metal seat & SS diaphragm

Pressure control: various ranges between 7-70 kpa & 1,210 1,900 kpa

* Options: Low flow trim in all sizes, threaded BSPT, BSPP, NPT or Flanged end

The post MK58FT 58A Back Pressure Reg appeared first on Braeco.

MK5800HP HP Back Pressure Reg

titan — Tue, 24 Mar 2015 06:06:36 +0000

MK5800HP is a high pressure, piston style Pressure Sustaining or Back Pressure Regulating valve for use on high pressure industrial gas & liquid services to 4,000 psi (276 bar). It offers exceptional accuracy with high capacity and easy in-line servicing. It is available with hard seat (Class III or IV shut-off) or soft seat (class VI). 316L body, Stellite, Vespel or PTFE seat, 316ss Pison, 17-4pH orifice & cylinder, bun-N or Viton o-rings, NPT or flanged Ansi 150/300/600/1500#

Pressure Control ranges: 400 psi -2,500 psi

The post MK5800HP HP Back Pressure Reg appeared first on Braeco.

MK57 Pilot Op Back Pressure Reg

titan — Tue, 24 Mar 2015 06:06:36 +0000

Jordan MK57 series is a pilot operated Pressure Sustaining or Back Pressure valve and provides greater accuracy and lower offset than can be achieved with self acting valves. It is available in sizes 1/2″-6″ (Cv’s 5.0-395) and consists of a main valve with a small, pilot valve. The Mk57 combines the short stroke of the sliding gate with the action of a pilot valve to create a faster, more accurate response (less droop as flows increase). Can be used where greater accuracy is required than self acting valves or where control systems are not an option.

– Suitable for steam, water, oil, gas and chemicals.
– Body materials available: cast iron, ductile iron, carbon steel & stainless steel.
– Available with BSPT or NPT threaded ends (1/2”→2”) or flanged Ansi 150/300, DIN PN10/16 25/40 (1/2”→6”)

– Several adjustable pressure ranges from 140-310 kpa→552-1,280 kpa)

* Options: Low differential pressure pilot, airloaded pilot.

The post MK57 Pilot Op Back Pressure Reg appeared first on Braeco.

MK56 Air Loaded Back Pressure Reg

titan — Tue, 24 Mar 2015 06:05:55 +0000

MK56 uses air (or gas) loaded on top of the diaphragm, instead of a conventional regulator where a spring applies the loading force that determines the set pressure. It has no spring or pilot and has the same rangeability (40:1) as a MK57, considered to be the most accurate regulator in the range.

By eliminating the spring, the regulator has almost no droop but the big advantage is being able to remotely control the set pressure and the wide pressure range that can be controlled. A conventional regulator might be able to regulate between 200-900 kpa but the MK56 could be loaded to provide upstream pressure control between a few kpa and then be adjusted right up to the maximum body pressure of the valve (890 psi for SS body). No spring changes..just adjust the pressure being loaded on the dome. The dome loading can be done by a loading station but the simplest method is just by using a JPR regulator from the Low Flow section or a conventional Air Filter Regulator. Adjust the regulator to a little over 5 kpa and the MK56 regulates the pressure to 5 kpa…..increase the air pressure to a little over 1200 kpa and the MK56 regulates to 1,200 kpa etc

Maximum inlet pressure- BZ 3,450 kpa; DI 4,140 kpa; WCB/316SS (6,550 kpa)

* Options: Low flow trim, stainless teel, buna or viton diaphragm, BSPP, BSPT, NPT or flanged.

The post MK56 Air Loaded Back Pressure Reg appeared first on Braeco.

Model RFT Pressure Sustaining Valve (316ss, screwed)

titan — Tue, 24 Mar 2015 06:04:52 +0000

Elite model RFT is a 316ss self acting pressure sustaining valve suitable for fluids & gasses.

Available in ½” → 2” (Cv’s from 2.4 to Cv25) and the main materials are 316SS with NBR or Viton diaphragm and seals.
Valve has threaded BSP female ends.
Maximum inlet pressure-2500 kpa (362 psi)
Maximum temp- 100°C or 180°C
Adjutable pressure ranges – 100-500 kpa; 400-1,000 kpa

* Options: NPT, all 316SS adjusting bolt/locknut, pressure gauge

The post Model RFT Pressure Sustaining Valve (316ss, screwed) appeared first on Braeco.

Model RFF Pressure Sustaining Valve (316ss, flanged)

titan — Tue, 24 Mar 2015 06:04:52 +0000

Elite model RFF is a 316SS self acting pressure sustaining valve suitable for fluids, air and steam.

Available in ½” → 6” (Cv’s 2.4-250) and the main materials are 316SS with NBR or Viton diaphragm and seals.
Valve has flanged ends which can be drilled to suit Ansi 150# or AS Table D/E, Cv’s from 2.4 to Cv250
Maximum inlet pressure-2500 kpa (362 psi)
Maximum temp- 100°C or 180°C for steam
Adjustable pressure ranges – 100-500 kpa; 400-1,000 kpa

* Options: All 316SS adjusting bolt/locknut, pressure gauge.

The post Model RFF Pressure Sustaining Valve (316ss, flanged) appeared first on Braeco.

BTS/BFS Pilot Operated Pressure Sustaining Valve (CI/DI/BZ/304SS/316SS)

titan — Tue, 24 Mar 2015 06:05:07 +0000

Elite model BTS/BFS uses a MFV (multi-function valve) which is directly fitted with a pressure sustaining valve pilot and is used primarily for water. Unlike conventional pilot operated valves which have a complex external pilot valve tubing assembly, this valve does not have any external piping or tubing, saving cost and simplifying installation.

It is available in BTS threaded version 1½”→ 2” (Cv’s 48-75) and BFS flanged version in 2”-14” (Cv’s 75-3,000) and the choice of materials for the main valve are cast or ductile iron with bronze trim, bronze, 304ss or 316ss. Diaphragm and seat material can be either NBR or Viton and the pilot valve can be bronze or stainless steel.

Valve has either threaded ends (1½”→ 2”) or flanged (1/2”-6”) which can be drilled to suit Ansi 150# or AS Table D/E.
Maximum inlet pressure-2500kpa (362 psi)
Maximum temp- 80°C
Sustained pressure ranges – 20-400 kpa; 300-1,000 kpa

* Options: Pressure gauge

The post BTS/BFS Pilot Operated Pressure Sustaining Valve (CI/DI/BZ/304SS/316SS) appeared first on Braeco.